3d printing, 

Автор: Cullen Bunn and Talibor Talajic
Название: Deadpool Minibus (New Printing)
ISBN: 1302901923 ISBN-13(EAN): 9781302901929
Издательство: Hachette Book Group
Рейтинг:
Цена: 41790.00 T
Наличие на складе: Нет в наличии.
Описание: Deadpool's wildest adventures are collected in one blood-soaked volume! What if Deadpool decided to kill everyone and everything that makes up the Marvel Universe? What if he followed that up by slaughtering the most famous fictional characters in classic literature? And what if he finally took aim at the ultimate target: himself? You'd have the fan-favorite "Deadpool Killogy," that's what! But when Deadpool battles Deadpool, will he win or perish? Yes! Then: Deadpool awakens from a food coma to find... the zombie apocalypse has occurred! Can the Merc with Mouth avoid becoming the Merc in their mouths?! And when Deadpool takes on Carnage, good-crazy battles bad-crazy, blood will flow and Deadpool will literally go to pieces!

Автор: Seeley Tim
Название: Hack/Slash Omnibus Volume 1 (Third Printing)
ISBN: 1607062739 ISBN-13(EAN): 9781607062738
Издательство: Image Comics
Рейтинг:
Цена: 28210.00 T
Наличие на складе: Невозможна поставка.
Описание: At the end of every horror movie, one girl always survives... in this case, Cassie Hack not only survives, she turns the tables by hunting and destroying the horrible slashers that would do harm to the innocent. Alongside the gentle giant known as Vlad, the two cut a bloody path through those who deserve to be put down... hard.

Автор: Russell Gonzalez Sara, Bennett Denise Beaubien
Название: 3D Printing: A Practical Guide for Librarians
ISBN: 144225548X ISBN-13(EAN): 9781442255487
Издательство: Rowman & Littlefield Publishers
Рейтинг:
Цена: 95750.00 T
Наличие на складе: Есть у поставщика Поставка под заказ.
Описание: Planning and implementing a 3D printing service in a library may seem like a daunting task. Based upon the authors' experience as early adopters of 3D technology and running a successful 3D printing service at a large academic library, this guide provides the steps to follow when launching a service in any type of library. Detailed guidance and over 50 graphics provide readers with sage guidance and detailed instructions on: -planning a proposal -printer selection tips -preparing the location -addressing staff concerns for new service -developing service workflows and procedures -managing inevitable disasters -developing policies -conducting the "reference interview" for 3D printing -staff training tips -outreach activities This book brings into one place all the guidance you need for developing and implementing a 3D printing service in any library.

Автор: Harline, Craig E.
Название: Pamphlets, printing, and political culture in the early dutch republic
ISBN: 9401081115 ISBN-13(EAN): 9789401081115
Издательство: Springer
Рейтинг:
Цена: 81050.00 T
Наличие на складе: Есть у поставщика Поставка под заказ.
Описание: This book resulted from a desire to understand the role of pamphlets in the political life of that most curious early modern state, the Dutch Republic. In short, I began to view pamphlets not as repositories of historical facts but as a historical phenomenon in their own right.

Автор: Daly, Angela
Название: Socio-legal aspects of the 3d printing revolution
ISBN: 1137515554 ISBN-13(EAN): 9781137515551
Издательство: Springer
Рейтинг:
Цена: 53100.00 T
Наличие на складе: Есть у поставщика Поставка под заказ.
Описание: This book is the first expert analysis of 3D printing from a legal perspective and provides a critical assessment of the extent to which existing legal regimes can be successfully applied to, and enforced vis-a-vis, 3D printing.

Автор: Horvath, Joan Cameron, Rich
Название: 3d printing with mattercontrol
ISBN: 1484210565 ISBN-13(EAN): 9781484210567
Издательство: Springer
Рейтинг:
Цена: 27910.00 T
Наличие на складе: Есть у поставщика Поставка под заказ.
Описание: Part 1: The 3D-Printing Ecosystem

Chapter 1. The Desktop 3D Printer

Chapter 2. What is MatterControl?

Chapter 3. Downloading and Configuring MatterControl

Part 2: The 3D-Printing Process

Chapter 4. Making a 3D Model

Chapter 5. Slicing a 3D Model

Chapter 6. Controlling your 3D Printer

Chapter 7. Material Considerations

Chapter 8. Special Cases

Автор: Micallef, Joe
Название: Beginning design for 3d printing
ISBN: 1484209478 ISBN-13(EAN): 9781484209479
Издательство: Springer
Рейтинг:
Цена: 41920.00 T
Наличие на складе: Есть у поставщика Поставка под заказ.
Описание: This book will demystify the design process for 3D printing, providing the proper workflows for those new to 3D printing, eager artists, seasoned engineers, 3D printing entrepreneurs, and first-time owners of 3D printers to ensure original ideas can be 3D printed.

Автор: Schmidt Christine
Название: Print Workshop: Hand-Printing Techniques and Truly Original Projects
ISBN: 0307586545 ISBN-13(EAN): 9780307586544
Издательство: Random House (USA)
Рейтинг:
Цена: 12250.00 T
Наличие на складе: Есть у поставщика Поставка под заказ.
Описание: Offers ideas for things to make and use, such as jar labels, pillows and a stationary set. This title leads the readers through a crash-course on printing with techniques, materials and surfaces.